LF (125kHz/134,2kHz) Units

multi standard reader/writer for industrial applications for 125kHz
easy start in transponder technology without large investments
multi-Tag compatible for Philips Hitag1, Hitag-S, EM V4102 / V4001/V4002/Unique, EM V4150 / V4050 / Titan ISO 11784 / 11785 / FDX-B
two built-in antennas (∅ 30 mm / 125 mm) selectable via protocol
software update possible (Flash memory)
interface: RS232 / USB (opt) / Ethernet (opt)
housing (IP65)
CE in preparation

Detailed datasheet [download]

SIR-6001 reader for industrial applications
EEX - approved ("ZONE 1") II-2G EEX me IIC T4 Reader/Writer (internally the approved Scemtec module STK-4 EEX is used)
multi-Tag compatible: standard: H4002 (UNIQUE) and HITAG-1 option: further tag types on request
software update possible (Flash memory)
type of interface SIR-600x (RS-232 / RS485)
housing: standard: DIN-rail housing with screw terminals, option: IP65 enclosure on request
power supply: 12V-DC / 24V-DC, low noise, 200mA
fast antenna multiplexer to connect two external antennas
EEX - approved antenna SAT-A2-EX-125kHz available
two digital inputs and two digital outputs
, available for combination of Scemtec reader and Scemtec antennas

Detailed datasheet [download]

Special RFID long range reader for rough industrial environment
reading distance up to 75 cm with ISO-card tag (depending on antenna area)
Contactless reading of different types of transponders V4150 (read only mode), EM4002 (read only), Hitag_S under development
Interfaces: RS-232, USB and Ethernet optional
Protective system / Protective class: IP 65 (EN 60529) / I (IEC1010-1/VDE041)
different types of antennas available
1 Control Output (relay with potential free cantacts)
1 Status Output (relay with potential free cantacts)

Detailed datasheet [download]

HF (13.56MHz) Units

13,56 MHz RFID reader/writer for industrial mid range applications
reading/writing of 13,56 MHz ISO15693 and ISO18000-3 labels or transponders, e.g. EM Microelectronic-Marin SA EM4034, EM4035 and EM4135 tags
reading distance up to 35 cm with integrated antenna and use of an RFID card/label of ISO-card size
conection of an external antenna is possible
anticollision: simultaneous reading/writing of many labels/transponders in the antenna field
internal jumper for tuning of the internal antenna to "metal environment"
software update possible (Flash memory)
housing (IP65)

Detailed datasheet [download]

13,56 MHz RFID reader/writer for long range applications
Multi-Tag compatible (1): I-CODE, TAG-IT and ISO 15693 I-Code UID and EPC and as an option VarioSens, EM Microelectronic-Marin SA EM4034, EM4035 and EM4135 compatible
Reading distance up to 1,2 m with single antenna [test condition: 60 cm antenna, “ISO-Card”-size Tag] and up to 2,0 m with gate antenna
Anti-collision
EAS Function (electronic article surveillance)
Interfaces: RS-232, USB (implemented), Ethernet (option)
Option Antenna Multiplexer for multiplexing of up to 4 antennas with full power (4 Watt)
Option reader synchronisation 1 master and up to 3 slaves
Output power selectable by software (within approval range)
Standing Wave Ratio (SWR) measurement included
Different types of antennas available
2 digital inputs and 8 digital outputs
Relay output is available to switch higher loads (potential free)
Standard housing IP 66
Firmware can be updated via RS 232 (flash on board)

(1) For details of supported transponder modes and functions, please refer to scemtec STX/ETX protocol specification.

Detailed datasheet [download]

13.56MHz RFID reader/writer for industrial mid range applications
reading/writing of 13,56 MHz ISO15693 and ISO18000-3 labels or transponders, e.g. EM Microelectronic-Marin SA EM4034, EM4035 and EM4135 tags
reading distance up to 70 cm with external antenna SAT-A40-LR-0-13MHz and use of a RFID card/label of ISO-card size
anticollision: simultaneous reading/writing of many labels/transponders in the antenna field(s)
up to 1.4W output power @ 50Ohms load
RS232, USB and Ethernet interface
software update possible (Flash memory)

For details of supported transponder modes and functions, please refer to scemtec STX/ETX protocol specification.

Detailed datasheet [download]